|
Product Details:
|
| Application: | Well Testing Operation | Usage: | Oil Well Suface Testing Operation |
|---|---|---|---|
| Material Class: | DD | Production Level: | PLS 3 |
| Production Level: | PR1 , PR2 | Standard: | API 6A |
| Product Name: | Surface Test Tree | Working Pressure: | 1440 Psi |
| Specification: | 3"FIG602 | Working Condiction: | Standard Serive Or Sour Service |
| High Light: | oil well testing equipment,surface test tree |
||
API 6A Well Surface Testing Oil Diverter Manifold
The oil produced by the separator can be directed through an oil manifold to the gauge tank, surge tank, production flowline or burner depending on the test circumstances. The manifold usually has five 2-in. ball valves.
From the gauge tank, the flow is piped to the oil manifold by way of a transfer pump. The pump boosts the pressure so that the flow can be supplied to a burner or reinjected into a flow- line. If a surge tank is used, the manifold serves the same purpose. In effect, the manifold directs the flow from the separator without interruption to the burner or flowline. For offshore tests, two burners are typically used to support continuous testing without respect to the prevailing wind direction. The oil manifold can direct flow to either the port or starboard burner without stop- ping the well test because of undesirable wind directions.
The skid-mounted oil manifold is fitted with five valves. Oil is directed through the manifold valves to one of three test components
starboard burner
port burner
storage tank
Service: H2S
Working pressure:1440psi
Inlet: 3" FIG 602
Outlet: 3" FIG 602
Valve type: Ball valve
Valve quantity: 5
Skid mounted.
| CHOKE MANIFOLD |
| Sour service: NACE MR0175 |
| Operating -20 to 250 deg F |
| Choke manifold shall have double block gate valves and bleed, to allow choke changes/replacements without interrupting the flow and for protection of the personnel and environment. |
| Chemical injection point across the choke for hydrate inhibition/mitigation. |
| 128/64ths " adjustable choke |
| 1 active + 1 backup |
| Full set of fixed beans in 2/64” increments from 8/64” to 48/64” and 4/64” increments from 48/64” to 128/64”. |
| 2 Bleed off ports upstream and downstream of choke bodies. |
| SURFACE SAFETY VALVE |
| Sour service: NACE MR0175 |
| Operating -20 to 250 deg F |
| Hydraulically fail safe gate valve, tied into ESD system. |
| DATA HEADER (Required 2ea) |
| 3" Fig 1502 10K Psi |
| Sour service: NACE MR0175 |
| Operating Temp: -20 to 250 deg F |
| Minimum number of ports. Compliant with double barrier philosophy : 6 |
| OIL MANIFOLD |
| 3"602 connection (Oil) and 4"602 connection (Gas): API SPEC 6A, ASME B16.34 (Valves associated with diverter manifolds) |
| Sour service: NACE MR0175 |
| Minimum 1440 psi rating |
| Temperature rating: 32 to 212 deg F |
| Outlets to burner boom. Valves to be interlocked or similarly mechanically controlled when ball valves supplied. |
| 5 way Manifold |
| GAS MANIFOLD |
| 4"602 connection (Gas): API SPEC 6A, ASME B16.34 (Valves associated with diverter manifolds) |
| Sour service: NACE MR0175 |
| Minimum 1440 psi rating |
| Temperature rating: 32 to 212 deg F |
| Outlets to burner boom. Valves to be interlocked or similarly mechanically controlled when ball valves supplied. |
| 3 way Manifold |
| HIGH PRESSURE PIPING |
| Minimum nominal size: 3" Fig 1502 connection |
| Minimum working pressure: 10K psi |
| Sour service: NACE MR0175 |
| Pipework with integral or welded hammer unions |
| Sufficient quantity / length of high pressure of 50mtr piping and 40pc 90 deg elbow to connect upstream package |
| LOW PRESSURE PIPING |
| Sufficient quantity / length of low pressure piping and elbow to connect downstream package, including vent and relieve lines |
| Sour service: NACE MR0175 |
| Pipework with integral or welded hammer unions |
| Well test pipework will be suitably restrained to anchor points corresponding to the maximum pressure to which it is tested |
About JC Wellhead
Jingcheng Petroleum Machinery Manufacturing Co.,Ltd was established in 2008, we are specialized in design and manufacturing of the oilfield wellhead equipment. We - YCJC are a registered supplier for CNPC, GWDC, CCDC in China.
YCJC also engaged in abroad marketing, through these years of efforts, our wellhead equipment is exported to many countries, such as Thailand, UAE, Iran, Brazil, Argentina, USA etc. and enjoyed good reputation from the customers.
The wellhead equipment we manufacture and supply include casing head, tubing head, casing spool, tubing spool, Gate valve, Choke valve, Check valve, X-mas tree, VR plug, Tubing hanger, casing hanger, Running tool, Wear bushing, spacer spool, flange adapter, union flange, Hammer union, Elbow, swivel joint, block cross, Block Tee, companion flange, instrument flange, weldneck flange, FC gate, FC seat, FC stem, API Clamp, API Clamp Hub
Contact Person: Lee M
Tel: 86-13319268557
Fax: 86-29-81779342
